50% beeswax
30% Red, Tacky Lucas High Temp Grease
10% Johnson's Paste Wax
5% Dexron II or Dexron III Trans. Fluid
5% STP Oil Treatment
But a forum member was nice enough to describe that in other units, and using a complete Red Tacky Lucas Grease:
24 ozs. = 3 cups - melted beeswax
14 ozs. = 1 3/4 cups - Red N Tacky , heat it..it doesn't really melt
4.6 ozs. = 2/3 cup - Johnsons Paste Wax - melted
2.3 ozs. = 1/3 cup - Dexron II or III ATF
2.3 ozs. = 1/3 cup- STP Oil Treatment
Note, 1/3 cup = 5 Tablespoons + 1 teaspoon
So I got several low cost supplies from Wally World, and from my local auto parts store:
![Image](http://m3coupe.com/Firearms/casting/Lube/20150210_134441.jpg)
I do my own electronics, so I have two hot ways to do surface mount reflow, so I tried one:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_152654_001.jpg)
For the Red grease, I open the end, and squeezed it out like toothpaste (tip from a forum member here):
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_152837.jpg)
Then used spatula to get the other end (as much as possible):
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_153053.jpg)
I am waiting for beeswax from another forum member, but before I knew of him I had ordered a small amount through Amazon, which happen to come in little pellets. Here I got about 20 oz - I will add the rest later, as I was not 100% everything would fit in my container (it did):
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_155713.jpg)
The wax:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_170602.jpg)
After I had the grease there for a while (while stirring it), I added the beeswax:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_155913.jpg)
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_160348.jpg)
But I was never able to get enough heat, quickly enough:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_160938.jpg)
So I tried my "better" hotplate:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_160950.jpg)
The mixture got hotter, and the beeswax started to melt a little, so I added the Johnson wax, and the two liquids (using these to measure per the instructions above):
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_170936.jpg)
Although I got more heat, it was not hot enough to really melt everything:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_171729.jpg)
Since I had everything mixed, I used my propane setup on the lowest level, and keep stirring it constantly:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_173129.jpg)
That worked well, but it also worked fast!. As soon as you get the wax melted you need to kill the fire and keep stirring:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_173600.jpg)
Since I knew I had the space, I went ahead and added the rest of the beeswax. Of course, I had to restart the fire for a short while, to get enough heat to melt the new beeswax:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_174039.jpg)
After I had everything melted uniformly, with no clumps, I poured the contents on two pans:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_180128.jpg)
I put them in the freezer for 1-2 hours, and then took them to my bench to cut up:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_191218.jpg)
Since it shrinks, it is easy to get out:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_191249.jpg)
Cut it with one of my small knives:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_191516.jpg)
After cutting the two plates into triangles and strips of various sizes, I used the non-stick foil and set them aside for future use:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150214_192457.jpg)
In a freezer bag for storage:
![Image](http://m3coupe.com/Firearms/casting/Lube/Bens_Red/20150215_101114.jpg)
I hope to try this with pan lubing pretty soon (working now on a custom kake kutter!).
Will