DIY hot blueing

Share your experience in caring for your favorite Rossi with other members or ask the question that you cannot find the answer to!
Post Reply
donhuff
1000 Shots
1000 Shots
Posts: 1650
Joined: 03 May 2013 10:14
Location: LaGrange Georgia
Has thanked: 7 times
Been thanked: 339 times

DIY hot blueing

Post by donhuff »

I did a little research on it and found that it can be done in a few different ways, and also using a few common ingredients.

The chems that I used were Spectracide stump remover which is reported to be near 100% potassium nitrate (salt peter). And common Lye drain cleaner (sodium hydroxide). I found a few different ratios, and that told me that I didn't have to be very specific about that part of the process. So I put some of one and some more of the other into a small steel vessel I had made to melt lye in for getting the varnish off of copper wire that I use for rewinding RC boat racing motors.

This little container was almost big enough to completely submerge a muzzle brake that I had made for one of my bolt action rifles. It takes a little while for the propane torch to heat the chems to the point that they go into a liquid, but once there, with the brake on a long piece of steel wire. I SLOWLY lowered the part into the caustic bath. After maybe 8-10 minutes I took it out, sprayed with water, then diped into water to cool it, and gave it a look. It was turning black pretty well. I buffed it down with 0000 steel wool, and degreased with brake cleaner. Dry with a het gun, and then put back into the solution for a while longer.

I would take it out occasionally to look at the progress and when I though it looked good enough, I cooled it down, cleaned with soapy water. Dried and then oiled it good and that's when it really turned dark. It looks about like the factory blue on my old Remington that it's screwed onto. So much of how the blueing looks, depends on how you finish the metal before you blue it.

This is a fairly dangerous way of doing this type of blueing because the molten chems have to get around 650-700 to go to a liquid. That's on top of the caustic nature of the chems. And I have read about a method of using the same chems but dissolving them in water and boiling your parts @ 275*F
I'll try that method next time so that I can immerse the whole part at once. But I think it turned out nice for a first try.
You do not have the required permissions to view the files attached to this post.
Don Huff

to bad those that know it all, cant do it all!
16" SS 92 357
20" BL 92 357
20" SS 92 44
20" BL 92 44
20" Bl 92 45C
20" Bl 92 454
SS Rio Grande 30-30
Bl Rio Grande 45-70
User avatar
Ranch Dog
Site Admin
Site Admin
Posts: 9398
Joined: 23 Jan 2012 07:44
Location: Inez, TX
Has thanked: 1837 times
Been thanked: 2281 times

Re: DIY hot blueing

Post by Ranch Dog »

You are on a DIY roll!
Michael
Image
User avatar
Mad Trapper
500 Shots
500 Shots
Posts: 540
Joined: 03 Aug 2013 14:04
Location: Daniel Boone Forest
Has thanked: 171 times
Been thanked: 144 times

Re: DIY hot blueing

Post by Mad Trapper »

That looks real good,
I use that Spectracide stump remover for nitrating coffee filter paper for making combustible cartridges for my 1860 army.
donhuff
1000 Shots
1000 Shots
Posts: 1650
Joined: 03 May 2013 10:14
Location: LaGrange Georgia
Has thanked: 7 times
Been thanked: 339 times

Re: DIY hot blueing

Post by donhuff »

Damit! now there's something else I gots to try and do.

Would that be nitro cellulose?
Don Huff

to bad those that know it all, cant do it all!
16" SS 92 357
20" BL 92 357
20" SS 92 44
20" BL 92 44
20" Bl 92 45C
20" Bl 92 454
SS Rio Grande 30-30
Bl Rio Grande 45-70
User avatar
Mad Trapper
500 Shots
500 Shots
Posts: 540
Joined: 03 Aug 2013 14:04
Location: Daniel Boone Forest
Has thanked: 171 times
Been thanked: 144 times

Re: DIY hot blueing

Post by Mad Trapper »

donhuff wrote:Damit! now there's something else I gots to try and do.

Would that be nitro cellulose?
I learned it from Mark Hubbs

User avatar
Mad Trapper
500 Shots
500 Shots
Posts: 540
Joined: 03 Aug 2013 14:04
Location: Daniel Boone Forest
Has thanked: 171 times
Been thanked: 144 times

Re: DIY hot blueing

Post by Mad Trapper »

I bought this kit, not the entire kit, just those three red pieces, the forming mandrel, base and funnel.
I make my own lube and use the coffee filters instead of cigarette papers, they are a bit more sturdy.
I use the elmer glue sticks for gluing.

donhuff
1000 Shots
1000 Shots
Posts: 1650
Joined: 03 May 2013 10:14
Location: LaGrange Georgia
Has thanked: 7 times
Been thanked: 339 times

Re: DIY hot blueing

Post by donhuff »

Well, that was interesting.

I have always wondered what would happen if you did that. Pretty much what I thought it would do. BOOM!!
Don Huff

to bad those that know it all, cant do it all!
16" SS 92 357
20" BL 92 357
20" SS 92 44
20" BL 92 44
20" Bl 92 45C
20" Bl 92 454
SS Rio Grande 30-30
Bl Rio Grande 45-70
Post Reply