Opening a Lee sizer
-
- 1000 Shots
- Posts: 1599
- Joined: 31 Jul 2014 15:18
- Location: Dayton Oh
- Has thanked: 227 times
- Been thanked: 328 times
Opening a Lee sizer
Who here has opened up a Lee sizer and what did you do to make sure the hole stayed round? I need to get one in .457 and open it to .458 or 459 for the Wizard. He likes fat bullets .
Make smoke,
Make smoke,
Curt... makin' smoke and raising my carbon foot print one cartridge at a time
-
- 2000 Shots
- Posts: 3942
- Joined: 04 Feb 2014 05:30
- Location: SoCal Loco
- Has thanked: 137 times
- Been thanked: 610 times
Re: Opening a Lee sizer
Have you considered contacting Lee for the right part rather than modifying existing?Ohio3Wheels wrote:Who here has opened up a Lee sizer and what did you do to make sure the hole stayed round? I need to get one in .457 and open it to .458 or 459 for the Wizard. He likes fat bullets .
Make smoke,
http://leeprecision.com/custom-lube-and-size-kit/
- Ranch Dog
- Site Admin
- Posts: 9399
- Joined: 23 Jan 2012 07:44
- Location: Inez, TX
- Has thanked: 1838 times
- Been thanked: 2281 times
Re: Opening a Lee sizer
I've tried it a couple of times using lapping compound and soft lead bullets and then simply by trying to hone it. Oh, I also tried using a reamer. Nothing was successful I thought so I have stuck with special ordering them as Archer suggested. In the long run with thousands of bullets passing through them they cost next to nothing.Ohio3Wheels wrote:Who here has opened up a Lee sizer and what did you do to make sure the hole stayed round? I need to get one in .457 and open it to .458 or 459 for the Wizard. He likes fat bullets.
Michael
-
- 1000 Shots
- Posts: 1599
- Joined: 31 Jul 2014 15:18
- Location: Dayton Oh
- Has thanked: 227 times
- Been thanked: 328 times
Re: Opening a Lee sizer
Unfortunately .457 is the biggest they make. Guess I'll see what they want for a special order .459.Archer wrote:Have you considered contacting Lee for the right part rather than modifying existing?Ohio3Wheels wrote:Who here has opened up a Lee sizer and what did you do to make sure the hole stayed round? I need to get one in .457 and open it to .458 or 459 for the Wizard. He likes fat bullets .
Make smoke,
http://leeprecision.com/custom-lube-and-size-kit/
Make smoke,
Curt... makin' smoke and raising my carbon foot print one cartridge at a time
-
- 1000 Shots
- Posts: 1599
- Joined: 31 Jul 2014 15:18
- Location: Dayton Oh
- Has thanked: 227 times
- Been thanked: 328 times
Re: Opening a Lee sizer
Just took a look. Lee asks $34 for a custom sizer with a 6 to 8 week lead time. Since I have a Lyman 450 I took a quick look at Track of the Wolf and Buffalo Arms, both have the sizer for under $30. Think maybe I'll go with the 450 this time.
Make smoke,
Make smoke,
Curt... makin' smoke and raising my carbon foot print one cartridge at a time
- akuser47
- Founding Member
- Posts: 5070
- Joined: 12 Feb 2012 11:43
- Location: ohio
- Has thanked: 1266 times
- Been thanked: 482 times
Re: Opening a Lee sizer
Lee custom made parts are usually 3 weeks faster then quoted. I understand though the need to get it faster. Keep us posted to how the 450 works out for you.
- Ranch Dog
- Site Admin
- Posts: 9399
- Joined: 23 Jan 2012 07:44
- Location: Inez, TX
- Has thanked: 1838 times
- Been thanked: 2281 times
Re: Opening a Lee sizer
Buffalo Arms also has quite a few custom sizes for the Lyman sizer.Ohio3Wheels wrote:Just took a look. Lee asks $34 for a custom sizer with a 6 to 8 week lead time. Since I have a Lyman 450 I took a quick look at Track of the Wolf and Buffalo Arms, both have the sizer for under $30. Think maybe I'll go with the 450 this time.
Make smoke,
Michael
-
- 1000 Shots
- Posts: 1599
- Joined: 31 Jul 2014 15:18
- Location: Dayton Oh
- Has thanked: 227 times
- Been thanked: 328 times
Re: Opening a Lee sizer
Yep, it looks like they make sizes that Lyman doesn't. The 450 i an old work horse I've had for years a lot of lead and lube have been through it and it just keeps working. With roper care I don't think I'll wear it out .
Make smoke,
Make smoke,
Curt... makin' smoke and raising my carbon foot print one cartridge at a time
-
- Posts: 18
- Joined: 15 Sep 2013 20:26
- Location: Saskatchewan
- Has thanked: 5 times
- Been thanked: 6 times
Opening a Lee sizer
Lee sizers are easy to open up. I use a rod a little smaller than the opening wrapped with wet or dry sand paper lubed with penetrating fluid like WD40. Then just push down and roll it on an old mouse pad. Depending on how much I need to go, I start out with 320 grit and once close start going finer until I finish polish with 800 grit. I find screwdrivers work good for smaller sizers and for my .457" I used a 1/4" drive socket extension. They all need to be strait, obviously. This has worked for me with both the Lee and Lyman size dies without fail. Keeps them nice and concentric. I believe there is a YouTube video of someone doing it this way.
- Missionary
- Founding Member
- Posts: 588
- Joined: 21 Mar 2012 15:47
- Location: Peru
- Has thanked: 9 times
- Been thanked: 145 times
Re: Opening a Lee sizer
Good morning
I have lapped or reamed to larger diameter numerous sizing dies but mostly Lyman.
If it is just a few thousanths I use a rod with metal paper wrapped around it inserted into the die and rolled on a hard flat surface like you are rolling out pie crust. I have a set of hole gauges that get used to check real diameter.
If it is going to be a major diameter change the first is applied enough heat to get the sizer red hot and let it air cool. Soft metal works much easier. On a drill press I either drill to the rough hole size then ream or just ream if the change is not real drastic. Then finish off with the rod wrapped in metal paper on the flat hard surface.
I use to roll the sizer on my pant leg which also works but it will wear out the top of your pants if you do this often.
Mike in Peru
I have lapped or reamed to larger diameter numerous sizing dies but mostly Lyman.
If it is just a few thousanths I use a rod with metal paper wrapped around it inserted into the die and rolled on a hard flat surface like you are rolling out pie crust. I have a set of hole gauges that get used to check real diameter.
If it is going to be a major diameter change the first is applied enough heat to get the sizer red hot and let it air cool. Soft metal works much easier. On a drill press I either drill to the rough hole size then ream or just ream if the change is not real drastic. Then finish off with the rod wrapped in metal paper on the flat hard surface.
I use to roll the sizer on my pant leg which also works but it will wear out the top of your pants if you do this often.
Mike in Peru
Way down south in Arequipa, Peru till June 2020.