You've probably already checked it since it unfortunately sounds like taking it apart has replaced shooting it as your hobby. ;~)
But I was just wondering Spent, and I don't know if it would give ya the problem your talking about, but have you looked at the receiver end of the tube to make sure it's not rolled inward or burred or something that might be casing an occasional hitch as you load?
Also, have you tried taking out the tube spring and just dropping the follower down the tube to see how easily it moves in the tube? Again, may not actually cause the problem you are talking about, but stranger things have happened?
Loading .357's issues
-
- Posts: 232
- Joined: 19 Aug 2014 21:41
- Location: Kentucky
- Has thanked: 40 times
- Been thanked: 95 times
Re: Loading .357's issues
"As to the species of exercise, I advise the gun. While this gives moderate exercise to the body, it gives boldness, enterprise, and independence to the mind." Thomas Jefferson
- rman
- 500 Shots
- Posts: 673
- Joined: 18 May 2014 11:47
- Location: Kansas
- Has thanked: 160 times
- Been thanked: 125 times
Re: Loading .357's issues
I had the same problem with my .357. I did a lot of fiddling with the spring and loosening the screw that holds the loading gate. There seems to be just a tiny bit of play in my gate. After numerous tries, it started working better, but wasn't 100%. Now that I've shot 250-300 rounds through it, it works much more reliably. I use mine for competition, so I only load 5 at a time. It has worked perfectly for the last 2 matches.
At my age, there IS nothing better than shooting.
- Spentcase
- Posts: 15
- Joined: 01 Oct 2014 18:15
- Location: NY
- Has thanked: 4 times
- Been thanked: 1 time
Re: Loading .357's issues
It sure seems that way.jdb wrote:You've probably already checked it since it unfortunately sounds like taking it apart has replaced shooting it as your hobby. ;~)
I did lightly sand the mag tube mouth in the receiver previously. I'll check on the metal plug just in case.
Maybe it just need more breaking in. I've shot over 250 rounds in her, as well as worked the action at least 700 times, plus polished the internals. Maybe my rifle is just a slow learner.
“You can't have no idea how little I care.”
― Monte Walsh
― Monte Walsh
- Spentcase
- Posts: 15
- Joined: 01 Oct 2014 18:15
- Location: NY
- Has thanked: 4 times
- Been thanked: 1 time
Re: Loading .357's issues
Up to now I've put 125 rounds through her, and only had one jam. I think I finally pinpointed the problem. Me.
As I mentioned before, almost all jams were when I chambered the second round. I think It has to do with how I get the last round pushed in the loading gate. If I slip or don't push deep enough, I believe that the last round fails to push the one ahead of it into the tube. So the last round in comes up on the carrier fine with I cock it, but the round before it seems to be not in the tube all the way and engaged by the cartridge stop, so it comes out and gets the round ahead of it coming through on the next lever engagement jammed up against it. Hope that makes sense.
As I mentioned before, almost all jams were when I chambered the second round. I think It has to do with how I get the last round pushed in the loading gate. If I slip or don't push deep enough, I believe that the last round fails to push the one ahead of it into the tube. So the last round in comes up on the carrier fine with I cock it, but the round before it seems to be not in the tube all the way and engaged by the cartridge stop, so it comes out and gets the round ahead of it coming through on the next lever engagement jammed up against it. Hope that makes sense.
“You can't have no idea how little I care.”
― Monte Walsh
― Monte Walsh
- Silas Longshot
- Posts: 13
- Joined: 02 Mar 2015 20:20
- Location: GA
- Has thanked: 2 times
- Been thanked: 12 times
Re: Loading .357's issues
As I posted when I started up with the group, my m92 24" octo-barrel .357 was near a complete rebuild from day one. https://survivingurbancrisis.wordpress.com/ In case it may be needed here, since this was a gun show purchase, and no warranty available, it seems.
- Spentcase
- Posts: 15
- Joined: 01 Oct 2014 18:15
- Location: NY
- Has thanked: 4 times
- Been thanked: 1 time
Re: Loading .357's issues
Silas,
Thanks for the post and the link to your excellent troubleshooting tutorial. I've done some of the things you did, and see how I can do a few more to insure a consistent feed. If and when spring and summer decide to finally make an appearance up here again, I have to run some cartridges through her again to test out the mods.
Thanks for the post and the link to your excellent troubleshooting tutorial. I've done some of the things you did, and see how I can do a few more to insure a consistent feed. If and when spring and summer decide to finally make an appearance up here again, I have to run some cartridges through her again to test out the mods.
“You can't have no idea how little I care.”
― Monte Walsh
― Monte Walsh