Problem With The Buckmark Slide Sticking
- Jaybm
- 500 Shots
- Posts: 739
- Joined: 09 May 2014 17:15
- Location: SC
- Has thanked: 118 times
- Been thanked: 139 times
Problem With The Buckmark Slide Sticking
I really like this Browning .22LR, very accurate but you do have to be
very careful placing your finger on the trigger. It's really soft, I'd
almost call it a hair trigger. But knowing that you just put your brain
in gear and be careful to keep it pointed down range. That's not the
problem.
The problem is after the pistol has been stored awhile I can't rack the
slide. Yesterday I got the RO to rack it and after the first time it's fine.
It seems like the mating surfaces of the slide and barrel are so perfectly
machined they " stick ".
I do use Mobil One ... sparingly ... and wonder if the minuscule amount
that may remain on those surfaces is the culprit ? I'm almost tempted to
put a toothpick between them before putting the gun away.
Anyone have a similar problem ? Ideas definitely welcome ... Jim
Oh, this only happens with the Browning, not a problem with the Bersa's
or Sig.
very careful placing your finger on the trigger. It's really soft, I'd
almost call it a hair trigger. But knowing that you just put your brain
in gear and be careful to keep it pointed down range. That's not the
problem.
The problem is after the pistol has been stored awhile I can't rack the
slide. Yesterday I got the RO to rack it and after the first time it's fine.
It seems like the mating surfaces of the slide and barrel are so perfectly
machined they " stick ".
I do use Mobil One ... sparingly ... and wonder if the minuscule amount
that may remain on those surfaces is the culprit ? I'm almost tempted to
put a toothpick between them before putting the gun away.
Anyone have a similar problem ? Ideas definitely welcome ... Jim
Oh, this only happens with the Browning, not a problem with the Bersa's
or Sig.
Gun Control Means Hitting The Target
-
- 250 Shots
- Posts: 333
- Joined: 17 Jun 2013 08:12
- Location: Kingsland, GA
- Has thanked: 100 times
- Been thanked: 50 times
Re: Problem With The Buckmark Slide Sticking
I've only had this problem years ago when I used to swear by WD40 for everything. It's pretty bad about leaving a sort of sticky varnish behind. I've used auto trans fluid but not any motor oil in guns so I don't know if any motor oils leave a varnish.
-
- 1000 Shots
- Posts: 1599
- Joined: 31 Jul 2014 15:18
- Location: Dayton Oh
- Has thanked: 227 times
- Been thanked: 328 times
Re: Problem With The Buckmark Slide Sticking
We've got two Buckmark Silhouettes from way back and don't recall that problem. I used Gunslick sparingly on the slides and they seemed okay. Mobil One being synthetic shouldn't leave anything but slick behind. I'll be interested in any findings and solutions.
Make smoke,
Make smoke,
Curt... makin' smoke and raising my carbon foot print one cartridge at a time
- Jaybm
- 500 Shots
- Posts: 739
- Joined: 09 May 2014 17:15
- Location: SC
- Has thanked: 118 times
- Been thanked: 139 times
Re: Problem With The Buckmark Slide Sticking
Maybe the ole man is just weak ?
This has happened to me more than several times and it's kind of
embarrassing to ask someone to rack your pistol. Might try using
some Hoppe's on those surfaces.
In fact I'm gonna do that right now !!! If I can rack it , might
have to ask the wife for help.
Oh yeah, another rainy day in SC ... Jim
This has happened to me more than several times and it's kind of
embarrassing to ask someone to rack your pistol. Might try using
some Hoppe's on those surfaces.
In fact I'm gonna do that right now !!! If I can rack it , might
have to ask the wife for help.
Oh yeah, another rainy day in SC ... Jim
Gun Control Means Hitting The Target
- akuser47
- Founding Member
- Posts: 5070
- Joined: 12 Feb 2012 11:43
- Location: ohio
- Has thanked: 1266 times
- Been thanked: 482 times
Re: Problem With The Buckmark Slide Sticking
If it were me next time out, first thoroughly clean it i mean the hammer , the sear the disconnect, clean everything like it was a white glove test by your armorer before turn in to armory. Then relube it mobile synthetic shouldnt be causing this it's so slick. After this shot 500 or more rounds through her then repeat clean her out again relube put up and check on later to see if it's still happening. I'm thinking she's not broken in yet, and just needs good cleaning and lube until mating surfaces are fully married together. However this is only true if it is a new gun or old gun with low round count. Keep us posted to your findings.
- Jaybm
- 500 Shots
- Posts: 739
- Joined: 09 May 2014 17:15
- Location: SC
- Has thanked: 118 times
- Been thanked: 139 times
Re: Problem With The Buckmark Slide Sticking
Well it racked just fine after only sitting for a day.
With the scarcity of .22LR for so long I suppose the Buckmark
could be considered having a low round count.
What did surprise me was how dirty the Q-tip with the Hoppe's
was after wiping down those surfaces. I usually don't "miss" those
areas ?
Stay tuned ... Jim
With the scarcity of .22LR for so long I suppose the Buckmark
could be considered having a low round count.
What did surprise me was how dirty the Q-tip with the Hoppe's
was after wiping down those surfaces. I usually don't "miss" those
areas ?
Stay tuned ... Jim
Gun Control Means Hitting The Target
-
- 2000 Shots
- Posts: 3942
- Joined: 04 Feb 2014 05:30
- Location: SoCal Loco
- Has thanked: 137 times
- Been thanked: 610 times
Re: Problem With The Buckmark Slide Sticking
The paperwork that came with my High Standard back in 1972 says to clean it when necessary with KEROSENE. I've often noted that Hoppe's seems to smell like there's some Kerosene in it.
I have become a great believer in Slip2000 EWL in that it does NOT tack up and is pretty insensitive to temperature.
I've never had any issues with my Smith 41, Ruger MKIIs, High Standard or my buddy's BuckMark with the slide sticking. I DO need to replace the trigger/sear spring on the High Standard but that's because it was/is weak when I acquired it.
In the past I've used Gunslick and Tetra on slide rails with very good results.
I have also used Tri-Flow bicycle chain lube.
I do NOT like RemOil.
WD40 is for use as cosmoline ONLY that is only when you are looking for a moisture displacing layer to be removed quickly OR to be allowed to SET into a VARNISH like consistency should it be applied to ANYTHING.
I have become a great believer in Slip2000 EWL in that it does NOT tack up and is pretty insensitive to temperature.
I've never had any issues with my Smith 41, Ruger MKIIs, High Standard or my buddy's BuckMark with the slide sticking. I DO need to replace the trigger/sear spring on the High Standard but that's because it was/is weak when I acquired it.
In the past I've used Gunslick and Tetra on slide rails with very good results.
I have also used Tri-Flow bicycle chain lube.
I do NOT like RemOil.
WD40 is for use as cosmoline ONLY that is only when you are looking for a moisture displacing layer to be removed quickly OR to be allowed to SET into a VARNISH like consistency should it be applied to ANYTHING.
- GasGuzzler
- Moderator
- Posts: 2752
- Joined: 02 Nov 2015 19:54
- Location: Cooke County, TX
- Has thanked: 310 times
- Been thanked: 452 times
Re: Problem With The Buckmark Slide Sticking
Dang...I use CLP and RemOil depending on need. I like them over M1 because I'm kinda lazy sometimes and I like the aerosol. In cases were people use M1, I use Wahl trimmer oil....because it's what I have that's handy. I do have a qt of M1 on the bench too...it gets used four pour/soak operations mostly.
I actually do use WD40, but only to dissolve some substances....then it's cleaned off.
Not to be contrary but to offer my opinion....I'd clean it with CLP, lightly coat it with RemOil, then wipe it down.
I actually do use WD40, but only to dissolve some substances....then it's cleaned off.
Not to be contrary but to offer my opinion....I'd clean it with CLP, lightly coat it with RemOil, then wipe it down.
Last edited by GasGuzzler on 08 Nov 2015 19:49, edited 1 time in total.
__________________________________________________________________________________________
I've always been crazy but it's kept me from going insane.
I've always been crazy but it's kept me from going insane.
- akuser47
- Founding Member
- Posts: 5070
- Joined: 12 Feb 2012 11:43
- Location: ohio
- Has thanked: 1266 times
- Been thanked: 482 times
Re: Problem With The Buckmark Slide Sticking
I've use clp not familiar with clr unless we're talking cleaning sinks n such in bathrooms. Is that the clr u speak of? Might be a new thing I've not heard of yet.
- GasGuzzler
- Moderator
- Posts: 2752
- Joined: 02 Nov 2015 19:54
- Location: Cooke County, TX
- Has thanked: 310 times
- Been thanked: 452 times
Re: Problem With The Buckmark Slide Sticking
Fat brained it, my fingers are thin, just messed up but thanks. You're correct.
CLP
I fixed a spellie too...
CLP
I fixed a spellie too...
__________________________________________________________________________________________
I've always been crazy but it's kept me from going insane.
I've always been crazy but it's kept me from going insane.