Cz 455 varmint in a grs stock
- akuser47
- Founding Member
- Posts: 5070
- Joined: 12 Feb 2012 11:43
- Location: ohio
- Has thanked: 1266 times
- Been thanked: 482 times
- Coop 45
- Posts: 124
- Joined: 25 Aug 2014 05:38
- Location: Australia
- Has thanked: 14 times
- Been thanked: 37 times
Re: Cz 455 varmint in a grs stock
Well, I finally found some time to do some work on my cz. Straight out of the box it was shooting some very nice groups, until I fiddled with it. First thing I did was to check that the barrel was properly floated, which it wasn't. After a bit of sanding to fix this up it was back out to the range. Put a target at 50m, fire the first shot and its a full hand span to the right, next shot and its 2" left. Next few are at point of aim. The problem is the inletting. The CZ reciever is curved at the back. The inletting is flat. Where it was touching the barrel it was helping to keep it in the one place and now it can move. Once its had a few shots it settles down but will throw about every fifth shot out of the group. Worse is when it goes in one of the racks at the range the first shot is a good 4" off.
So, next task is a bedding job. Good thing I've got some devcon left over from a previous job.
On the good side I did manage to get it down to comp weight of 4 kg. The stock is a bit shorter, a bit more ventilated at the fore end, and missing the recoil pad, but it makes weight.
So, next task is a bedding job. Good thing I've got some devcon left over from a previous job.
On the good side I did manage to get it down to comp weight of 4 kg. The stock is a bit shorter, a bit more ventilated at the fore end, and missing the recoil pad, but it makes weight.
"Shoot straight you bastards, don't make a mess of it" Captain Harry "Breaker" Morant, last words to his firing squad.
92 45 Colt 20" stainless
92 45 Colt 20" stainless
- akuser47
- Founding Member
- Posts: 5070
- Joined: 12 Feb 2012 11:43
- Location: ohio
- Has thanked: 1266 times
- Been thanked: 482 times
Re: Cz 455 varmint in a grs stock
sounds good glad she is working out for you. quick question do you like devcon over acraglass better?
-
- 2000 Shots
- Posts: 3942
- Joined: 04 Feb 2014 05:30
- Location: SoCal Loco
- Has thanked: 137 times
- Been thanked: 610 times
Re: Cz 455 varmint in a grs stock
The smith that did my match Garand favored the Devcon Steel compound.
http://www.sniperforums.com/forum/diy/3 ... ixing.html
http://www.sniperforums.com/forum/diy/3 ... ixing.html
- Coop 45
- Posts: 124
- Joined: 25 Aug 2014 05:38
- Location: Australia
- Has thanked: 14 times
- Been thanked: 37 times
Re: Cz 455 varmint in a grs stock
I use the devcon simply because that's what I used on the first rifle I bedded and I've never had any problems with it so I keep using it. I've actually never used anything else so I couldn't comment on the merits of one over the other. Not that I've bedded many rifles either.
I hope to bed it some time this month, then I'll get down to some serious ammo testing.
I hope to bed it some time this month, then I'll get down to some serious ammo testing.
"Shoot straight you bastards, don't make a mess of it" Captain Harry "Breaker" Morant, last words to his firing squad.
92 45 Colt 20" stainless
92 45 Colt 20" stainless
- mr surveyor
- 1000 Shots
- Posts: 1610
- Joined: 16 Mar 2013 11:20
- Location: NE Texas
- Has thanked: 488 times
- Been thanked: 293 times
Re: Cz 455 varmint in a grs stock
how much weight will the bedding add back to it
jd
jd
-----------------------------------------------------------------------------------------
Guns - They aren't really yours until you void the warranty!
Guns - They aren't really yours until you void the warranty!
- akuser47
- Founding Member
- Posts: 5070
- Joined: 12 Feb 2012 11:43
- Location: ohio
- Has thanked: 1266 times
- Been thanked: 482 times
Re: Cz 455 varmint in a grs stock
Bedding shouldn't add much other than few ounces here n there. Unless there is serious stock fit issues.
- Coop 45
- Posts: 124
- Joined: 25 Aug 2014 05:38
- Location: Australia
- Has thanked: 14 times
- Been thanked: 37 times
Re: Cz 455 varmint in a grs stock
I've got 30 grams to play with. For any scoped rifle I use in a match I always get it to weight with the scope caps on. That way if it gets heavier I can take them off. That's an extra 15 grams.
It does happen, I went to a shoot in Queensland, a bloke I knew went up a month earlier to do some fishing. It was very humid and his centre fire stock sucked up 15 grams of water and put him over. He was walking up and down the range asking who had a saw.
I'll put some pics up when I'm done.
It does happen, I went to a shoot in Queensland, a bloke I knew went up a month earlier to do some fishing. It was very humid and his centre fire stock sucked up 15 grams of water and put him over. He was walking up and down the range asking who had a saw.
I'll put some pics up when I'm done.
"Shoot straight you bastards, don't make a mess of it" Captain Harry "Breaker" Morant, last words to his firing squad.
92 45 Colt 20" stainless
92 45 Colt 20" stainless
- Coop 45
- Posts: 124
- Joined: 25 Aug 2014 05:38
- Location: Australia
- Has thanked: 14 times
- Been thanked: 37 times
Re: Cz 455 varmint in a grs stock
Well.......................
After bedding the action it's still shooting like a pile of €^+#. The very first shot from a cold barrel is going about 4-6 inches high and slightly to the right. The next shots are all on point of aim. Let it cool down for a few minutes and the next shot will be high and right again. After much searching on the various forums it may be a tight barrel. A few others had the same issue of first shot flyers in cz's and they found that with cz's sometimes having a slightly tighter than normal barrel that they were getting leading occurring right where the rifling starts.
The recommended fix is to scrub the first few inches with something like JB bore paste, and then clean the rifles every few hundred rounds. If this works I'll be very happy.
After bedding the action it's still shooting like a pile of €^+#. The very first shot from a cold barrel is going about 4-6 inches high and slightly to the right. The next shots are all on point of aim. Let it cool down for a few minutes and the next shot will be high and right again. After much searching on the various forums it may be a tight barrel. A few others had the same issue of first shot flyers in cz's and they found that with cz's sometimes having a slightly tighter than normal barrel that they were getting leading occurring right where the rifling starts.
The recommended fix is to scrub the first few inches with something like JB bore paste, and then clean the rifles every few hundred rounds. If this works I'll be very happy.
"Shoot straight you bastards, don't make a mess of it" Captain Harry "Breaker" Morant, last words to his firing squad.
92 45 Colt 20" stainless
92 45 Colt 20" stainless
- Coop 45
- Posts: 124
- Joined: 25 Aug 2014 05:38
- Location: Australia
- Has thanked: 14 times
- Been thanked: 37 times
Re: Cz 455 varmint in a grs stock
Finally got in some jb bore paste and gave the first 100mm of the barrel a good scrub. This has fixed the first shot flyer problem straight away. I used the rifle in a major regional match last month. You know things are working when the first shot from a cold barrel hits dead centre. I just have a little cosmetic work to fix up where I took a bit of extra timber out of the stock.
"Shoot straight you bastards, don't make a mess of it" Captain Harry "Breaker" Morant, last words to his firing squad.
92 45 Colt 20" stainless
92 45 Colt 20" stainless