Revolver powders

Extend your shooting experience while reducing the cost of your ammunition!
golfish
500 Shots
500 Shots
Posts: 795
Joined: 23 Oct 2012 17:25
Location: Alta Loma, Ca
Has thanked: 26 times
Been thanked: 166 times

Revolver powders

Post by golfish »

Happy New Years to all +guns
I'm going to start reloading. I've been reading about it for a few years, the last few months, it's about all I've been doing.
It's not easy to find info on pistol caliber rifle/carbine loads. I figure this might be the best place. I bought some 2400 powder for these loads. You guys seem to really like "lil gun" so I will try that also.

What powder are you guys using for 38sp loads from your handguns ? I bought a pound of Unique and some 158 grain hard cast bullets. I have a lot of once fired brass.

Also, do you have a powder that you use for both handgun and rifle loads ?

This is just for plinking, now that I've retired and have a few buddies to shoot with, I'm shooting more. I thought it would be fun to hand load and see what I can come up with.

Thanks for your help
User avatar
mr surveyor
1000 Shots
1000 Shots
Posts: 1608
Joined: 16 Mar 2013 11:20
Location: NE Texas
Has thanked: 486 times
Been thanked: 292 times

Re: Revolver powders

Post by mr surveyor »

Both Unique and A2400 are excellent to get started on .38 spl and .357 mag. It's just my opinion, but I'd suggest at least 3-4 (small batch) loading/testing/shooting sessions of .357 mag and A2400 loads and the same with .38 spl and Unique loads. Staying well within published load weights and working with various charge weights for the individual batches is definitely a means to get both experience and confidence. Tinkering with the abundant numbers of other powders can wait for a while as the confidence increases and the feeling of satisfaction gets fed.

My late mentor did a good job of convincing me that Unique and A2400 would handle most every handgun type round I'd have - maybe not the absolute best at any caliber, but at least adequate in almost all. A2400 for the "magnums" and Unique for all the rest.

Again, just my opinion, the best two powder choices to begin with.


jd
-----------------------------------------------------------------------------------------
Guns - They aren't really yours until you void the warranty!
golfish
500 Shots
500 Shots
Posts: 795
Joined: 23 Oct 2012 17:25
Location: Alta Loma, Ca
Has thanked: 26 times
Been thanked: 166 times

Re: Revolver powders

Post by golfish »

Thank you Sir, I'm hoping to get some good loads asap so I can stock up. Living in California and having a new gun hating governor sux. They already make it hard to buy ammo, in 6 months it will be worse.
Ohio3Wheels
1000 Shots
1000 Shots
Posts: 1599
Joined: 31 Jul 2014 15:18
Location: Dayton Oh
Has thanked: 227 times
Been thanked: 328 times

Re: Revolver powders

Post by Ohio3Wheels »

I load for both the 357 and the 45 Colt for both the Rossi '92s and the two Black Hawks and I tend to shoot close to the same loads in both although I tend to back off a little on the revolver loads vs the rifles. Arthritis in the hand and wrist will only stand for so much pounding. For hunting H110, LilGun and 296 with heavy bullets. For fun lighter bullets and either True Blue or Trail Boss. Follow one or two good manuals and have fun.

Make smoke,
Curt... makin' smoke and raising my carbon foot print one cartridge at a time Image
User avatar
HarryAlonzo
500 Shots
500 Shots
Posts: 989
Joined: 31 Dec 2015 00:20
Location: Sedona
Has thanked: 248 times
Been thanked: 281 times

Re: Revolver powders

Post by HarryAlonzo »

There isn't much data specific to pistol calibers in carbines. The way I see it, the revolver is the weaker of the two, so that's what should drive the load. You can count on higher velocities from your carbine, in most cases. The "Ballistics by the Inch" website is a good reference.
golfish
500 Shots
500 Shots
Posts: 795
Joined: 23 Oct 2012 17:25
Location: Alta Loma, Ca
Has thanked: 26 times
Been thanked: 166 times

Re: Revolver powders

Post by golfish »

Ohio3Wheels wrote:I load for both the 357 and the 45 Colt for both the Rossi '92s and the two Black Hawks and I tend to shoot close to the same loads in both although I tend to back off a little on the revolver loads vs the rifles. Arthritis in the hand and wrist will only stand for so much pounding. For hunting H110, LilGun and 296 with heavy bullets. For fun lighter bullets and either True Blue or Trail Boss. Follow one or two good manuals and have fun.,
Thank you for the advice, my head has been spinning from all this reading. The press kit, dies, powders, primers and other stuff arrives tomorrow from Brownells. I'm lucky to have a little reloading shop about 10 miles away.
HarryAlonzo wrote:There isn't much data specific to pistol calibers in carbines. The way I see it, the revolver is the weaker of the two, so that's what should drive the load. You can count on higher velocities from your carbine, in most cases. The "Ballistics by the Inch" website is a good reference.
Ballistics by the inch, I was told about this site, I couldn't recall the name. Thank you.


FWIW, I have a 24" R92 and the 20" short rifle. I also have a Marlin 1894c. I've always read that these two calibers peak from the 16" barrel. This stuff is very interesting to me.
9x80Drilling
Posts: 107
Joined: 09 Nov 2015 23:51
Location: Dolores, Colorado
Has thanked: 289 times
Been thanked: 36 times

Re: Revolver powders

Post by 9x80Drilling »

golfish, welcome to the fascinating, rewarding, and educational world of reloading. I've been reloading since I was in my early teens, well more than 50 years ago. I hope you find and enjoy a wealth of benefits from the hobby. My older brother repeats the mantra, "Reload to shoot; Shoot to reload."

You've gotten good sound suggestions from these other posters. If you aren't following RD's Lee Loader forum, I'd suggest you jump in over there, too. Sorry, I can't remember if you post there. Many, if not most of us here also read and post over there.

A couple of hints I can give, which I think are rather standard. Only have one can of powder on your bench at a time. And, take it easy; think things through each and every session. Even if you have not changed anything in your setup since the last session, think it all through before you start in.

Reloading is incredibly rewarding. It's safe and easy if you keep your wits about you.

Good luck and keep us filled in.
golfish
500 Shots
500 Shots
Posts: 795
Joined: 23 Oct 2012 17:25
Location: Alta Loma, Ca
Has thanked: 26 times
Been thanked: 166 times

Re: Revolver powders

Post by golfish »

9x80Drilling wrote:

A couple of hints I can give, which I think are rather standard. Only have one can of powder on your bench at a time. And, take it easy; think things through each and every session. .
Thank you for the tips. It's funny that you mention the powder. I think back to all of the videos that I've watched, I can't think of one that had more than one can of powder on the bench. That's a good tip.

I did join Michael's Lee-loader forum but I had to lie about the press, mine is a Rock Chucker :)
nvbirdman
Posts: 32
Joined: 28 Mar 2015 21:56
Location: Nevada
Been thanked: 14 times

Re: Revolver powders

Post by nvbirdman »

Before you go hog wild loading ammo, be sure to check the length of your cartridges.
Load a few and make sure they will function in your gun. My 92 is very particular when it comes to Cartridge OverAll Length (COAL).
9x80Drilling
Posts: 107
Joined: 09 Nov 2015 23:51
Location: Dolores, Colorado
Has thanked: 289 times
Been thanked: 36 times

Re: Revolver powders

Post by 9x80Drilling »

golfish, no worries on using an RCBS press. My bench has two "green presses" set up on it, both a Reloader Special from 1972 and a Partner from the 90s. I prime with a basic C style Lee press. Nearly all the dozens of dies I use are Lee, however.
Post Reply